Se voc est usando o Windows e tem instalado um driver Epson , os.Click the items below to go to the messages and solutions.This message is displayed when MAC address filtering is enabled and the printer's MAC address has not been registered to the access point. (Canada) where you can download drivers, view manuals, get FAQs, or e-mail Epson.NEW Epson Artisan 730 Wireless All-in-One Color Inkjet Printer C11CB18201 4.5 out of. Click theicon on your desktop (or in Applications/Epson Software/Guide folder on Mac OS X). Make sure the paper is under the tabs on the edge. Start Here 4 Slide the edge guides against the paper, but not too tight.
![]() Epson Artisan 730 Printer Mac OS XOther devices on the network are turned on If you have checked the above points, perform network setup using EpsonNet Setup.Confirm IP address, subnet mask, and default gateway setup. Check that devices that want to use the printer, such as the PC, are on the same network. Check that the power is on for devices, such as the PC, that want to use the printer. Place your printer close to the PC you want to connect to.Confirm the connection and network setup of the PC or other device.Connection using the EpsonNet Setup is available.Contact your network administrator for assistance. Restpre a file on quicken for mac 2017If the default gateway address is incorrect, set the correct address using the printer's LCD panel.Your current default gateway address is displayed in C (Network Status) under Default Gateway.-Entered security key/password is correct-Index of the security key/password is set to the first number-IP address, subnet mask, or default gateway setup is correct The device specified as a default gateway is turned on The default gateway address set manually for the printer is correct Confirm default gateway setup. If the network address is incorrect, set the correct address using the printer's LCD panel.If you cannot change the settings using your printer, make settings using EpsonNet Setup.Your current IP address, subnet mask, and default gateway are displayed in C (Network Status).Setup is incomplete. The network address for the printer is the same as the one for other devices Network devices such as the modem, hub, and router are turned on If multiple keys are registered, check if you have entered the first key registered.-Connection and network setup of the PC or other device is correct You can register multiple security keys for the access point in WEP security mode. Perform network setup using the printer's LCD panel and enter the correct security key. If your printer is not listed, the security key may be incorrect. Start EpsonNet Setup on the PC that is using the same network as the printer.If your printer is listed in the printer list, set the IP address for the printer on the IP address setup screen. ![]() (When the router is a DHCP server or when there is another DHCP server in the home network, set a value that does not conflict with the IP address allocated by the DHCP server.)IP address for the router (or access point): 192.168.1. In the final segment, set a unique numerical value within a range of 1 to 254. All IP addresses are written in segments of four numerical values (for IPv4). For details, see the instruction manual for the router (or access point). Check the IP address for the router (or access point) connected to your PC. If you want to use "Manual" to set the printer's IP address, see the following to set the IP address and subnet mask. If you have problems printing or scanning, improve your wireless network environment.Signal interference can be caused by other wireless networks being used in nearby rooms or buildings. Remove any obstacles between the access point and the printer.*A router/access point channel conflict has been detected. Place the printer close to the access point If you have problems printing or scanning, improve your wireless network environment.Due to low signal strength, printing speed may be slow or printing may be interrupted.Perform the following to improve the environment: Also, the gateway uses the same value as the IP address for the access point.As well as the network status/connection check report, the following messages are displayed to let you know what other factors in your network environment need to be improved.*Signal strength is low. 3If you are using your printer in a small-scale network, 255.255.255.0 is set for all network devices for the subnet mask. Confirm network name (SSID).You are connecting to a different access point.Change the SSID for the access point you want to connect to, and then perform network setup for your printer again.*No more devices can be connected. Signal interference can be caused by other wireless networks being used in nearby rooms or buildings.*Multiple network names (SSID) that match your entered network name (SSID) have been detected. If you have problems printing or scanning, improve your wireless network environment.Due to low signal strength, printing speed may be slow or printing may be interrupted. A router/access point channel conflict has been detected.
0 Comments
Leave a Reply. |
AuthorIvy ArchivesCategories |